vcut07b1-hd1 www.vishay.com vishay semiconductors rev. 1.1, 31-may-12 1 document number: 84137 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 bidirectional symmetrical (bisy) single line esd-protection diode in llp1006-2l marking (example only) bar = pin 1marking x = date code y = type code (see table below) features ? ultra compact llp1006-2l package ? low package profile < 0.4 mm ? 1-line esd-protection ? working range 7 v ? low leakage current i r < 0.1 a ? low load capacitance c d = 14 pf ? esd-protection acc. iec 61000-4-2 30 kv contact discharge 30 kv air discharge ? soldering can be checked by standard vision inspection; no x-ray necessary ? pin plating nipdau (e4) no whisker growth ? e4 - precious metal (e.g. ag, au, nipd, nipdau) (no sn) ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 20855 21129 1 2 21121 xy ordering information device name ordering code taped units per reel (8 mm tape on 7" reel) minimum order quantity vcut07b1-hd1 VCUT07B1-HD1-G4-08 8000 8000 package data device name package name type code weight molding compound flammability rating moisture sensitivity level soldering conditions vcut07b1-hd1 llp1006-2l u 0.72 mg ul 94 v-0 msl level 1 (according j-std-020) 260 c/10 s at terminals absolute maximum ratings parameter test conditions symbol value unit peak pulse current acc. iec 61000-4-5; t p = 8/20 s; single shot i ppm 4a peak pulse power pin 1 to pin 2 acc. iec 61000-4-5; t p = 8/20 s; single shot p pp 60 w esd immunity contact discharge acc. iec 61000-4-2; 10 pulses v esd 30 kv air discharge acc. iec 61000-4-2; 10 pulses 30 kv operating temperature junction temperature t j - 40 to + 125 c storage temperature t stg - 55 to + 150 c electrical characteristics (pin 1 to pin 2 or pin 2 to pin1) (t amb = 25 c, unless otherwise specified) parameter test conditions/remarks symbol min. typ. max. unit protection paths number of lines whic h can be protected n channel --1lines reverse stand-off voltage max. reverse working voltage v rwm --7v reverse voltage at i r = 0.1 a v r 7--v reverse current at v rwm = 7 v i r --0.1a reverse breakdown voltage at i r = 1 ma v br 7.3 - - v reverse clamping voltage at i pp = 1 a v c -912v at i pp = i ppm = 4 a - - 15 v capacitance at v r = 0 v; f = 1 mhz c d -1416pf at v r = 2.5 v; f = 1 mhz - 11 - pf
vcut07b1-hd1 www.vishay.com vishay semiconductors rev. 1.1, 31-may-12 2 document number: 84137 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 cut the spikes with vcut07b1-hd1: the vcut07b1-hd1 is a bidirectional and symmetrical (bisy) esd-protection device which cl amps positive and negative overvoltage transients to ground. connected between the signal or data line and the ground the vcut07b1-hd1 offers a high isolation (low leakage current, low capacitance) within the spec ified working range. due to the short leads and small package size of the tiny llp1006-2l package the line inductance is very low, so that fast transients like an esd-strike can be clamped with minimal over- or undershoots. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - esd discharge current wave form acc. iec 61000-4-2 (330 ? /150 pf) fig. 2 - 8/20 s peak pulse current wave form acc. iec 61000-4-5 fig. 3 - typical capacitance c d vs. reverse voltage v r fig. 4 - typical reverse voltage v r vs. reverse current i r 0 % 20 % 40 % 60 % 80 % 100 % 120 % - 10 0 10 20 30 40 50 60 70 80 90 100 time (ns) discharge c u rrent i esd rise time = 0.7 ns to 1 ns 53 % 27 % 20557 0 % 20 % 40 % 60 % 80 % 100 % 010203040 time (s) i ppm 20 s to 50 % 8 s to 100 % 20548 12 14 16 8 10 12 4 6 0 2 - 8 - 6 - 4 - 2 0 2 4 6 8 f = 1 mhz pin 2 - 1 v r (v) c d (pf) 22630 i r (a) v r ( v ) 6 8 10 0 2 4 - 6 - 4 - 2 - 10 - 8 0.01 0.1 1 10 100 1000 10 000 pin 2 - 1 22631
vcut07b1-hd1 www.vishay.com vishay semiconductors rev. 1.1, 31-may-12 3 document number: 84137 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 5 - typical peak clamping voltage v c vs. peak pulse current i pp fig. 6 - typical clamping performance at + 8 kv contact discharge (acc. iec 61000-4-2) fig. 7 - typical clamping performance at + 8 kv contact discharge (acc. iec 61000-4-2) fig. 8 - typical peak. clamping voltage at esd contact discharge (acc. iec 61000-4-2) v c ( v ) i pp (a) 22632 15 10 0 5 - 5 - 15 - 10 0 1 2 3 4 5 negative s urge po s itive s urge mea s ured acc. iec 6100-4-5 (8/20 s - wave form) pin 2-1 v c t (ns) 22633 50 60 70 2 30 40 0 10 20 - 20 - 10 - 10 0 10 20 30 40 50 60 70 80 90 pin 2-1 acc. iec 61000-4-2 + 8 kv contact di s charge v c-e s d (v) 0 10 20 - 20 - 30 - 10 - 50 - 40 - 70 - 60 -10 0 10 20 30 40 50 60 70 80 90 pin 2-1 acc. iec 61000-4-2 - 8 kv contact di s charge 22634 t (ns) v c-e s d (v) v c-esd ( v ) v esd (k v ) 40 60 0 20 - 20 - 40 - 60 0 5 10 15 20 25 negative di s charge po s itive di s charge acc. iec 61000-4-2 contact di s charge pin 2-1 22635 30 n s v c-e s d
vcut07b1-hd1 www.vishay.com vishay semiconductors rev. 1.1, 31-may-12 4 document number: 84137 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters (inches): llp1006-2l 20812 doc u ment no.:s8- v -3906.04-005 (4) re v . 5 - date: 21 april 2010 created - date: 13. j u ly. 2007 foot print recommen d ation: s older re s i s t ma s k s older pad 0.55 [0.022] 0.45 [0.018] 0.25 [0.010] 0.15 [0.006] 0.45 [0.018] 0.35 [0.014] 0.3 [0.012] 0.2 [0.008] 0.4 [0.016] 0.33 [0.013] 1.05 [0.041] 0.95 [0.037] s olderma s k opening 0.03 mea s ured middle of the package 0.05 [0.002] 0 [0.000] 0.125 [0.005] ref. 0.65 [0.026] 0.55 [0.022] 0.05 [0.002] 0.25 [0.010] 0.5 [0.020] 1 [0.039] 0.5 [0.020] 0.6 [0.024] 0.2 [0.008] orientation i d enti?cation
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
